Butuh Training?

Silakan ketik kebutuhan training Anda di sini. Ada lebih 14.000 topik dan 250.000 event sepanjang tahun 2024

MOTOR PROTECTION, TESTING, CONTROL & MAINTENANCE

ACARA

10 – 12 Maret 2020 | Rp 6.500.000 per peserta di Yogyakarta
14 – 16 April 2020 | Rp 6.500.000 per peserta di Yogyakarta
12 – 14 Mei 2020 | Rp 6.500.000 per peserta di Yogyakarta

Jadwal Training 2020 Selanjutnya …

 

 

MOTOR PROTECTION, TESTING, CONTROL & MAINTENANCE TRAINING OVERVIEW

It is estimated that electrical drives and other rotating equipment consume about 50% of the total electrical energy consumed in the world today (and this figure increases to 70% if you only consider industry.) The cost of maintaining electrical motors can be a significant amount in the budget item of manufacturing and mining industries. This course gives you a thorough understanding of electrical motor’s protection,control and maintenance and gives you the tools to maintain and troubleshoot electrical motors.You will gain a fundamental understanding of the protection, control and maintenance of electric motors and drives. Typical applications of electric motors in mining, manufacturing, materials handling, process control are covered in detail. The concluding section of the course gives you the fundamental tools in troubleshooting motors confidently and effectively.

 

MOTOR PROTECTION, TESTING, CONTROL & MAINTENANCE TRAINING BENEFITS

You will learn how to:

  • Specify protection requirements for motors
  • Maintain electrical motors
  • Specify speed control requirements for motors
  • Understand essentials of motors and drives
  • Detail the main issues with testing of motors
  • Prevent or at least minimise motor bearing failure
  • Troubleshoot and fix faults on motors and drives
  • Interface control circuits of motors with PLCs/DCSs
  • Reduce downtime on electrical motors
  • Improve plant safety
  • Improve plant throughput
  • Reduce your spares usage and requirements

 

MOTOR PROTECTION, TESTING, CONTROL & MAINTENANCE TRAINING CONTENT

  • FUNDAMENTALS OF MOTOR TECHNOLOGY AND CONSTRUCTION
    • Basic principles of rotating electric machines
    • Fundamental principles of speed control
    • Efficiency, torque, inertia, horsepower/power factor
    • Torque-speed curves
    • Induction/synchronous/wound rotor types
    • Basic construction and physical configuration, windings
    • Principles of operation and performance
  • THREE PHASE AC INDUCTION MOTORS
    • Components
    • Theory of operation
    • Induction motor design
    • Duty cycles
    • Insulation and Cooling requirements
    • Starting methods
    • Selecting motors
    • Types of faults, fault finding and testing of AC machines
    • Testing instrumentation
  • ENERGY LOSSES AND EFFICIENCY OF THREE PHASE AC INDUCTION MOTORS
    • Standards
    • Types of Losses
    • Tests for measurement and computation of losses and efficiency
    • Dynamometers
    • Principles of load application by braking
    • Torque measurement basics
    • Types of practical dynamometers
  • MOTOR FAILURE ANALYSIS
    • Frequent starts
    • High inertia
    • Inadequate cooling
    • Congestion on fan cover
    • Improper spacing at end of motor
    • Incorrect belt alignment
    • Solid belt guards
    • Excessive loading causing bearing clearance problems
    • Insulation failures
    • Bearing current problems
  • TESTING
    • Insulation life and resistance
    • Polarization index
    • Hipot
    • DC ramp test
    • Ac hipot
    • Capacitance test
    • Dissipation factor
    • Partial Discharge
    • Surge test
    • Mechanical testing & Online testing
  • BEARING FAILURE ANALYSIS
    • Bearing failures
    • Grease and greasing
    • Belt Drive aspects
    • Balance
    • Storage issues
    • Service factor loading
  • PROTECTION OF MOTORS
    • Thermal overload
    • Time constraints
    • Early relays and new digital relays
    • Starting and stalling conditions
    • Over Current / Overload
    • Under-voltage / Over-voltage
    • Under frequency
    • Pole slip / Out of step
    • Loss of excitation
    • Inadvertent energization
    • Over fluxing
    • Stall protection / acceleration time / Start up supervision / Time between starts
    • Unbalanced supply voltages
    • Negative sequence currents
    • De-rating factors
    • Earth faults – core balance, residual stabilising resistors
    • Calculation of protective relay settings
  •  MOTOR CONTROL
    • Power Circuit & Control Circuit
    • Full Online voltage starting
    • Reduced Voltage starting: Delta-star, Resistance, Reactor, Autotransformer
    • Soft start: Braking, Speed Control, Reversing
  • CONTROL SYSTEM FOR AC VARIABLE SPEED DRIVES
    • Overall control system
    • Power supply for the control system
    • Dc Bus charging system
    • VSD control loops (Open Loop/Closed loop)
    • Vector control
    • Current feedback in ac variable speed drives
    • Speed feedback from motor
  • INSTALLATION AND FAULT FINDING
    • General installation and environmental requirements
    • Power supply connections and earthing
    • Where to install contactors in power circuit
    • Installation of ac converters into metal enclosures

 

WHO SHOULD ATTEND?

Typical personnel who would benefit are:

  • Plant Engineer
  • Instrument Technicians
  • Engineering and design personnel
  • Operations personnel
  • Electrical Maintenance Technicians
  • Instrument and Control Engineers
  • Electrical Contractors
  • Electrical consulting engineers
  • Process control Engineers
  • Mechanical Engineers
  • Service Technicians

Maintenance Personnel

METHODS

  • Presentation
  • Discuss
  • Case Study
  • Evaluation
  • Simulation

 

INSTRUCTOR

Tugino, S.T., M.T. & Team
(expert in Electrical Engineering)

 

JADWAL TRAINING 2020

  • Batch 3 : 10 – 12 Maret 2020
  • Batch 4 : 14 – 16 April 2020
  • Batch 5 : 12 – 14 Mei 2020
  • Batch 6 : 09 – 11 Juni 2020
  • Batch 7 : 14 – 16 Juli 2020
  • Batch 8 : 11 – 13 Agustus 2020
  • Batch 9 : 08 – 10 September 2020
  • Batch 10 : 20 – 22 Oktober 2020
  • Batch 11 : 24 – 26 November 2020
  • Batch 12 : 15 – 17 Desember 2020
  • 08.00 – 16.00 WIB

Yogyakarta: Cavinton Hotel Yogyakarta; Neo + Awana Hotel Yogyakarta; Pesonna Malioboro Hotel Yogyakarta
Surabaya: Hotel Neo Gubeng Surabaya; Hotel Santika Pandegiling Surabaya
Malang: Ibis Styles Malang Hotel
Jakarta: Yello Hotel Manggarai Jakarta; Dreamtel Jakarta Hotel
Bandung: Serela Cihampelas Hotel Bandung; Grand Setiabudi Hotel Bandung; Grand Tebu Hotel Bandung
Bali: Ibis Bali Kuta Hotel; Hotel Neo + Kuta Legian Bali

In House Training : Depend on request

 

TUITION FEE TRAINING

Yogyakarta:

  • Publish Rate       : Rp 6.500.000,- / participant
  • Special Rate        : Rp 6.100.000,- / participant (min 4 participants from the same company)

Bandung/ Jakarta/ Surabaya/ Malang:

  • Publish Rate       : Rp 7.000.000,- / participant

Bali:

  • Publish Rate       : Rp 8.000.000,- / participant

 

FASILITAS TRAINING

INCLUDE:

  • Meeting Room at hotel, Coffe Break, Lunch
  • Module (hard & soft copy/flashdish)
  • Training Kit, Souvenir, Sertifikat
  • Airport pick up services
  • Transportation during training

EXCLUDE:

  • Penginapan peserta training
  • Pajak (Ppn 10 %)

 

PRACTICAL MOTOR PROTECTION, TESTING, CONTROL & MAINTENANCE

Formulir Pra-Pendaftaran Public Training / Permintaan Informasi Lebih Lanjut
  1. JENIS INFORMASI/TRAINING
  2. (required)
  3. (required)
  4. DATA PRIBADI
  5. (required)
  6. (required)
  7. (required)
  8. (valid email required)
  9. (required)
  10. (required)
  11. DATA PRE REGISTRATION (Tidak Mengikat)
  12. (required)
  13. PESAN UNTUK PENYELENGGARA TRAINING
  14. Captcha
 

cforms contact form by delicious:days

Tags:  , , , , , ,