PIPING & PIPELINE SYSTEM: DESIGN, SPECIFICATION, INSTALLATION & MAINTENANCE
ACARA
29 Januari – 01 Februari 2019 | Rp7.000.000,- di Bandung
26 Februari – 01 Maret 2019 | Rp7.000.000,- di Bandung
26 – 29 Maret 2019 | Rp7.000.000,- di Bandung
23 – 26 April 2019 | Rp7.000.000,- di Bandung
Jadwal Training 2019 Selanjutnya …
COURSE OBJECTIVES PIPING & PIPELINE SYSTEM
- To learn Codes, Standard and Regulations for Pipeline
- To learn Technical Pipeline Documentation
- To learn flow characteristic inside pipeline
- To learn optimization of the pipe size selection
- To learn pipeline design loads and be able to conduct stress analysis
- To understand the ANSI Codes and ASME Codes for pipeline
- To learn pipe support analysis & design
COURSE OUTLINE PIPING & PIPELINE SYSTEM
- Introduction pipeline & piping history
- Pipeline & piping enginnering basic
- Piping & pipeline material Selection
- Othert Component
- Piping & pipeline design
- Piping / Pipeline Welding Technology
- Piping & pipeline corrosion and anti corrosion technology
- Piping & pipeline Testing & Maintenance
- Case study
WHO SHOULD ATTEND
The course is intended for Piping engineers, mechanical engineers, maintenance engineers & supervisors, Service engineers & supervisors, technicians and inspectors responsible for the design, work over engineers & supervisors, plant Engineers and Petroleum Engineers.
INSTRUCTOR PIPING & PIPELINE SYSTEM
Ir. SYAHBARDIA, MT
alumni dari teknik mesin Institut teknologi Bandung, ITB (sarjana), dan teknik material ITB untuk program magister. Beliau pernah menjadi dosen di Politeknik ITB/POLBAN dan sekarang Beliau menjadi dosen di jurusan teknik di universitas Pasundan, Bandung. Beliau memiliki pengalaman lapangan praktis sebagai mechanical engineer ketika beliau bekerja, seperti di IPTN, PINDAD, dan PAL. Ir. Syahbardia,MT. sudah sering menjadi instruktur di training-training industri untuk perusahaan-perusahaan di Indonesia. Diantara judul-judul yang Beliau sampaikan adalah Predictive and Preventive Pump Maintenance, Compressor Characteristic Maintenance & Troubleshooting, Rotary Equipment Maintenance, Lubrication, Operation, Maintenance and Trouble Shooting, Materials Selection and Knowledge for Engineers, Centrifugal Compresor & Steam Turbine Performance, Welding Inspection, Turbine & Generator Operation, Boiler Water Treatment, Pump Operation and Maintenance, Electrical Motor Control System, Corrosion and Cathodic Protection, Fluid Flow Measurement, Generator Preventive Maintenance, Heavy Equipment Management, Preventive and Predictive Maintenance, dan lain-lain.
Durasi Training
4 hari
Jadwal Training Sistem Kontrol PLTA
- 29 Januari – 01 Februari 2019
- 26 Februari – 01 Maret 2019
- 26 – 29 Maret 2019
- 23 – 26 April 2019
- 25 – 28 Juni 2019
- 23 – 26 Juli 2019
- 27 – 30 Agustus 2019
- 24 – 27 September 2019
- 22 – 25 Oktober 2019
- 26 – 29 November 2019
Venue
Bandung (Aston Braga, Ibis Styles, Kagum Hotel)
Investment
- Rp 7.000.000,-
Termasuk
- Materi hand-Out
- Softcopy materi (Flash disk)
- Sertifikat
- ATK (NoteBook dan Ballpoint)
- Tas kerja 3in1
- Foto Training
- Meeting room di hotel berbintang
- Lunch dan 2x coffee break
- Transportasi untuk peserta dari hotel penginapan ke hotel tempat training
PIPING & PIPELINE SYSTEM: DESIGN, SPECIFICATION, INSTALLATION & MAINTENANCE